Is a Popsocket Suppose to Have the Stick Tack on It How to Make a Popsocket Sticky Again

Download Article

Download Commodity

PopSockets are very useful for getting a better grip on your phone, but they can get muddy with time and the adhesive that sticks it to the back of your phone tin can become loose and lose its stickiness. Afterward removing it from your telephone, merely soak it in water and scrub it with soapy h2o your PopSocket to make information technology look skilful as new and stick as if you bought it yesterday.

1. 1

   Fill a shallow dish with cold tap water. Catch a shallow dish, such as a pocket-sized bowl or a deep plate, and fill it with about .five in (i.3 cm) of very cold tap water. This is to ensure that you but soak the adhesive side of the PopSocket — y'all should make clean the plastic grip separately.

   • Fifty-fifty if your PopSocket is larger than normal, using only a .5 in (1.3 cm) layer of water will ensure that just the agglutinative side touches the water when information technology is extended.

2. 2

   Remove the PopSocket and identify it sticky-side down in the water. Dig your fingernail under the PopSocket to pry it off of your phone, then pull the plastic grip to it extend to its full length. Identify the agglutinative side down in the water so the plastic grip pokes higher up the surface of the water.

   • Be sure that your extended PopSocket rises above the surface and drain out water equally necessary to avoid getting the rest of it wet.^[1]

   Advertising

3. 3

   Let the PopSocket soak for about ten seconds, then remove it. Don't disturb the water and don't take it out earlier 10 seconds are up. Once x seconds have passed, quickly take it out of the water by the grip and shake off whatever excess water. Practice non let it soak for more than ten seconds or it could ruin the agglutinative. ^[two]

   • If you are concerned near ruining the agglutinative, run the PopSocket nether cold water for a few seconds instead, although soaking it is more effective.^[three]

4. 4

   Lay a paper towel down and place the PopSocket sticky-side upwardly. You tin utilize a regular kitchen towel or a linen towel, depending on what you accept readily available. Lay the PopSocket with the sticky side pointing up and the pattern and plastic grip touch the paper.^[4]

5. v

   Allow the agglutinative side of the PopSocket dry for 10 minutes. Go out your PopSocket to dry for 10 minutes at almost, and go along an eye on it as it dries to see if it finishes sooner.^[five] Avoid using a hair dryer or dabbing it with a towel or you could damage the adhesive and make it less sticky. Only permit it air dry, and swiftly re-attach information technology to your telephone the moment it is dry out by pressing the pasty side firmly onto the dorsum of your telephone.

   • Do non let your PopSocket dry out for more than 15 minutes at most or it may lose its ability to stick.
   • If yous accidentally exit it out, run it under cold water for a few seconds then let it dry out again, although be aware that information technology may non regain its stickiness.

Advertisement

1. 1

   Remove whatsoever additional stickers yous've added to the end of the PopSocket. If y'all added stickers to the PopSocket's grip, you will need to remove them before you make clean it. If the agglutinative is still good on the sticker experience gratuitous to put it dorsum on later on cleaning, otherwise you volition have to only throw it away and find a new one.

   • PopSockets usually come with some kind of design on the end of the grip, so even if you lot accept to remove any additional stickers y'all've added, it will still have an aesthetic design.^[6]

2. ii

   Remove the PopSocket and run the plastic grip nether cold water. Use your fingernail to pry the PopSocket off of your phone, then hold the adhesive side of the PopSocket and turn your water faucet to a low period on cold. Run only the plastic grip of the PopSocket under h2o — if you must, wrap the adhesive in a hand towel to prevent getting it wet and affecting its stickiness.

   • You can clean the adhesive separately, only if you get information technology wet before y'all're fix to clean information technology, y'all could cause the agglutinative to lose some of its stickiness. Wrap it or have care to non get it wet while cleaning the grip.

3. iii

   Scrub the plastic grip with the corner of a soapy rag, avoiding the adhesive. Concord the PopSocket by the sticky side once more and scrub the plastic grip with the corner of a soapy rag PopSocket. Have intendance to avoid getting soap on the adhesive, and only scrub the plastic parts of the PopSocket.

   • Scrub within the grooves of the PopSocket'south expandable middle section with a cotton swab soaked in soapy water.
   • Employ lxx percent rubbing alcohol to particularly stubborn stains or grime with a cotton swab, then rinse it nether water once again. Rubbing alcohol is great for removing stains as it evaporates quickly and leaves no damage.

4. iv

   Rinse the grip once once more, and then dry it with a paper towel or rag. Run the grip under water to get rid of soapy residue and rubbing alcohol, again taking care to avert getting the adhesive wet. Then, have a dry rag or a paper towel and dab the PopSocket dry until it is completely costless of water.^[vii] Press it firmly onto the dorsum of your phone with the sticky-side down.

   • You can also air dry the plastic grip. Aggrandize the PopSocket so balance it on its side on a paper towel. This prevents the agglutinative from sticking to the towel and will still let the grip to air dry out and drip dry out.

Advertisement

Inquire a Question

200 characters left

Include your e-mail accost to go a message when this question is answered.

Submit

Advertisement

• Subsequently re-attaching the PopSocket to your telephone, wait at least 1 hour before yous extend the grip and use it. This allows enough time for the agglutinative to fully stick to your phone, reducing the gamble of it detaching all of a sudden.^[8]

Thank you for submitting a tip for review!

Advertisement

• Avert using rubbing alcohol in a closed room, and have the PopSocket to a well-ventilated expanse to preclude inhaling rubbing alcohol fumes.

• Never let the sticky side of the PopSocket be exposed to air for more than 15 minutes, fifty-fifty when cleaning the plastic grip, as this destroys the adhesive.

Advertisement

About This Article

Thanks to all authors for creating a folio that has been read thirty,573 times.

Is this article upwards to engagement?

mayfieldwhaturest.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket